Need Appliance Repair Service? Have a general question?
We love solving problems! Let us know how we can help by reaching out below.
for Victoria, MN
Debbie - Victoria, MN
MICROWAVE WHIRLPOOL WOC75EC0HS00 "Checked connections at board for panel and harness to panel reseated all check ok. Cycled power to unit right side buttons for tools, light and oven power are unresponsive to touch will need new panel W11289288 which is showing eta tba office to xpart and contact for return with part availability ; ordrng 1 W11289288 (PANEL)"
DISHWASHER WHIRLPOOL WDT720PADM2 WP8268961x2 friction pads ripped at vadnais WPW10274922 hinges bent need to order at vadnais scheduled for Monday ; ordrng 2 WP8268961 (pad)s and 1 WPW10274922 (hinge)
DISHWASHER KITCHENAID KDHE404DSS0 "Explained to customer that just replacing the tub he will still have a leak. The tub is rusted all around sump which caused gasket to wear advised replacing sump with tub. WPW10554963 at Waterloo Iowa talked to tk only charge for part 154.04part 12.00ship total 174.14 customer said he is going to call KITCHENAID and get back to us if he wants to repair unit ; ordrng 1 WPW10554963 (pump&motor) and 1 WPW10681511 (tub-dishwr), used 1 Ship (Shipping/Handling) from stock"
DISHWASHER WHIRLPOOL WDT720PADM2 Need to order WPW10274921 right side hinge. See notes ; ordrng 1 WPW10274921 (hinge)
DRYER WHIRLPOOL WED90HEFC1 No error codes custmer says will dry on heavy duty but nothing else clothes still damp. Ran vent tester and was getting good gas poor electric advised to have professional vent company come and check entire vent. Also adjusted user dryness level settings in control to see if that helps as well sensors check ok in diag test.
REFRIGERATOR WHIRLPOOL WRF555SDFZ02 The tag on back of the unit was flapping around from the air blowing for condenser fan. Removed tag and tested. Waited for 5 mins to see if noise would come back.
REFRIGERATOR WHIRLPOOL WRT518SZFM00 Unit is in a non heated garage environment advised needs to be 55 + degrees to work properly per manual
MICROWAVE WHIRLPOOL WMH78019HZ1 Door was rubbing on frame causing it to catch and make grinding noise realigned and tested door.
DISHWASHER WHIRLPOOL WDT720PADM2 Found faulty wash motor quoted for repair customer to buy new collected 97.95
DRYER WHIRLPOOL WED90HEFC1 Customer states clothes not fully drying in normal. Unit is heating Found lint screen full of lint cleaned off vent tester shows poor venting for electric and dryness level was set to less on normal advised customer to have vent company come and clean vent advised customer for optimal drying to keep on normal or more dry for dryness level and to clean lint screen after every load.
RANGE WHIRLPOOL WFE525S0HW0 Installed the bake element and tested there is still a slight squeak pre heater to a higher temp 450 and let sit squeak is not present anymore
Kitchen Aid Dishwasher # KDTE204ESS1 Still having issue with the power supply. Tested voltage and polarity and tested fine. As soon as the unit tries to draw any more power than cycle selection, the display dims and powers off. Does the same thing when trying to go into diagnostic mode, as soon as unit tries to turn on all LEDs, it dims and shuts off. Monitoring voltage showed a drop to 75 voltage under load. Tried resetting board multiple times and it didn’t help anything. Tried resetting breaker and it worked for a little while then reverted back to original state so the problem may be in the breaker. Tried plugging in the unit under kitchen sink but this produced the same issue since both outlets are on the same circuit which would say it’s not a cord or outlet issue, but a supply issue
WDT720PADM2-Whirlpool Dishwasher-door opens really fast just kind of falls-Found that both friction pads had broken and fallen off. Installed new friction pads on the unit. All checks good and door is functioning better.; used 2 WP8268961 (FRICTION PAD) from stock, Job Cmpltd,
WFG515S0ES1-Whirlpool Range- front door panel damaged- Replaced door on the unit. After replacing door noticed was rubbing on drawer a little bit. Upon further inspection found that the unit must have been dropped on the front legs and it dented the frame and bowed the cabinet. This pushed up the drawer so it is higher than it is supposed to be. Talked to Andrew about this and he is going to look into it.; Job Cmpltd,