Need Appliance Repair Service? Have a general question?
We love solving problems! Let us know how we can help by reaching out below.

How can we help?

Local Reviews
for Shakopee, MN

Rated 5.0 out of 5 stars based on 5 customer reviews

Map of Shakopee, MN

great service




excellent communication


Map of Shakopee, MN

Excellent service





Map of Shakopee, MN

Great job




No conplaints


Map of Shakopee, MN

Sarah




Was given a 8-11 window...he arrived before 9 which was great! Was polite and helpful..super pleased!


Map of Shakopee, MN

Fast and Friendly Service





Nate A.

Nate A.

WASHER WHIRLPOOL WTW4616FW2 Pump was chattering loudly and wouldn’t drain out any water. Installed new pump and ran through recalibration and auto test. All checks ok and unit is functioning correctly once again.; pckd up 1 W10919003 (PUMP)

Near Shakopee, MN 55372
Joshua S.

Joshua S.

WASHER WHIRLPOOL WFW95HEDW0 Installed pressure switch heater assembly and tested cleared errors

Near Abbey Point, Shakopee, MN 55379
Ryan W.

Ryan W.

REFRIGERATOR WHIRLPOOL WRF555SDFZ07 Installed new ui and damper unit cooling when left advised to give 36 to 48 hrs for temps to regulate

Near Woodland Ave, Shakopee, MN 55379
Nate A.

Nate A.

COOKTOP JENNAIR JGC8536ADS Installed flame stability kit and new ignitor for the front right burner. Front right burner now ignites normally with no issues and the flames are much more stable when opening the cabinet below. If the cabinet below is opened quickly when the flame is on low it still goes out but it is much better than before.; used 1 Ship (Shipping/Handling) from stock

Near Raspberry Ln, Shakopee, MN 55379
Nate A.

Nate A.

DRYER WHIRLPOOL WGD5000DW3 Getting a vent restriction which was causing the heat to short cycle. Found the vent was disconnected inside the insulation sleeve which was likely disconnected during install. Took off insulation as the vent is in a heated basement and not needed and reconnected the vent with some tape. Now plenty of flow and all checks ok.

Near Anton Way, Shakopee, MN 55379
Joshua S.

Joshua S.

REFRIGERATOR WHIRLPOOL WRF555SDHV01 Found filter no put in properly installed filter and tested. Temps are normal explained to customer she can not block vents collected 97.95 due to issue being customer instruct

Near Mockingbird Ave, Shakopee, MN 55379
Joshua S.

Joshua S.

WASHER MAYTAG MVWB835DC3 FLund long fill error tested unit and found hot water would start to fill then stop then start and then stop again checked screen and it was good checked wiring and found harness to valve wasn’t pushed in all the way causing valve to lose power and stop energizing valve. Secured harness and tested unit is working correctly

Near Cedar Terrace, Shakopee, MN 55379
Nate A.

Nate A.

REFRIGERATOR WHIRLPOOL WRF989SDAM00 "Compressor was hot and not running on arrival. Took off connectors to compressor and reset and let compressor cool. Plugged back in and compressor started running. Let run for about 20 minutes but got no frost pattern. Still have silver EVAP is ff compartment. With pointers would need updated board kit, compressor, EVAP, dye drier, heater fascia kit, and board kit. S codes should cover most if not all but office will verify.; ordrng 1 W10143759 (drier (service)) and 1 W10276644 (compressor) and 1 W10619962 (heater) and 1 W10861908 (cntrl-elec) and 1 W10917531 (EVAPORATOR)"

Near Boulder Pointe, Shakopee, MN 55379
Ryan W.

Ryan W.

ICEMAKER WHIRLPOOL KUIC15POZP1 Unit was just starting to run a cycle on arrival made good sheet of ice and went to release it I about 20 minutes saw sheet hanging up on chill plate and not making its way down onto cutting grid. Chill plate has a lot of build up on it and is keeping sheet from dropping. Also found bin thermistor detached- not allowing proper ice proctions- Reinstalled thermistor - All components test and checkout ok

Near Langston Ct, Shakopee, MN 55379
Nate A.

Nate A.

COOKTOP JENNAIR JGC8536ADS "12002586 burner kit, WP74009336 ignitor are the parts needed. Burner kit will prevent the burners from going down when the cabinets are opened and allow a more even flame. Ignitor on the front right burner is sparking below the tip so it is cracked. Customer is going to let us know if they want to proceed with a repair."

Near Raspberry Ln, Shakopee, MN 55379
Nate A.

Nate A.

DRYER MAYTAG MGDB835DC4 Dryer had error codes for air flow and communication errors between the UI and main control. Reset all of the connections on the control and UI and we will see if that issue comes up again. If so will replace UI and main control. Customer also have airflow error. Good flow out the back so will need to contact builder to check how the unit is venting and what kind of exit was put on the exterior.

Near Oakridge Trail, Shakopee, MN 55379
Nate A.

Nate A.

DISHWASHER WHIRLPOOL WDF520PADW3 Installed new upper and lower spray arm on the unit. Ran the unit through a diagnostic test. All checks ok and both arms have good pressure.; pckd up 2 WP8269145 (brckt-mtg)s

Near Countryside Dr, Shakopee, MN 55379
Nate A.

Nate A.

OVEN WHIRLPOOL WFE320M0ES1 Installed new control in the unit and reapplied power. Unit is no longer displaying the f9 code. Tested to a 350 bake and all checks out ok with no issues.

Near Westwind Ave, Shakopee, MN 55379
Nate A.

Nate A.

WASHER AMANA NTW4516FW2 Sound customer was hearing was the drain pump. Removed the water from the unit and took off the drain pump hose. Looked to be a small piece of wire from some clothing stuck in the pump which was restricting it from running. After removing ran through a recalibration and auto test. All checks ok and is working correctly once again.

Near Pheasant Run St, Shakopee, MN 55379
Nate A.

Nate A.

OVEN WHIRLPOOL WFE320M0ES1 Bake element has a break in it on the rear left which is causing the no heat condition. Will need to replace element to fix the issues.; ordrng 1 WPW10308477 (elmnt-bake)

Near Westwind Ave, Shakopee, MN 55379
Nate A.

Nate A.

DRYER MAYTAG MDE9700AYW "Unit not heating. All thermostats and fuses check ok. Tested voltage while running and found the relay on the board was not passing voltage so the control will need to be replaced.; ordrng 1 WP35001153 (cntrl-elec), used 1 Ship (Shipping/Handling) from stock"

Near Minnesota St S, Shakopee, MN 55379
Nate A.

Nate A.

MICROWAVE AMANA UMV1160CW6 Installed new magnetron in the unit and ran a heat test with a cup of water. All checks ok and is heating correctly. Customer will continue to use and see if the issue comes up again.

Near Omega Dr, Shakopee, MN 55379
Ryan W.

Ryan W.

WASHER MAYTAG MVWB835DW3 Oxy siphon cap was not pushed down on tube so was not able to siphon properly ran auto test and manual valve test I which oxy dispenser worked properly. If continued issues with oxywould suggest replacement of main control since valve checks out ok.

Near Minnesota Valley Bluff Dr, Shakopee, MN 55379
James R.

James R.

GAS RANGE KITCHEN AID KSGB900ESS0 Installed main control ordered. Ran bake 350. All tested ok

Near Marschall Rd, Shakopee, MN 55379
Nate A.

Nate A.

MICROWAVE WHIRLPOOL WMH32519HZ3 "The right side of the microwave cabinet is bulged our from the control panel. Took off control panel to make sure that the cabinet was clipped in correctly. This checked ok, will need to verify with the dealer that this is a defect and not the way the unit is designed. If it is not supposed to be like that, the unit was likely dropped and the cabinet bent."

Near Foothill Trail, Shakopee, MN 55379
Ryan W.

Ryan W.

WASHER WHIRLPOOL WTW7340XW0 Bearing failure was locked up and drive hub seized hard to get off shaft will need new bearing shaft kit and drive hub customer declined will buy new unit

Near Parkway Ave, Shakopee, MN 55379
Ryan W.

Ryan W.

REFRIGERATOR KITCHENAID KBRP20EMSS System not cooling comp running suspect leak at evap and or green rotted discharge tube which is not available in parts diagram. Since discharge tube rotting and has been in water of pan system may be contaminated no repair

Near Wildwood Cir, Shakopee, MN 55379
Nate A.

Nate A.

GAS RANGE KITCHEN AID KSGB900ESS0 error of main oven sensor shorted. Oven sensor ohms out correctly from the board so board will need to be replaced as it is not seeing the sensor. Customer requesting a morning appointment.; ordrng 1 W11100100 (CONTROL)

Near Marschall Rd, Shakopee, MN 55379
Ryan W.

Ryan W.

REFRIGERATOR WHIRLPOOL WRV976FDEM01 Installed board and heater duplicate heater not here secured and took with duplicate control all test ok and operational when left

Near Spring Lake Court, Shakopee, MN 55379
Nate A.

Nate A.

DISHWASHER WHIRLPOOL KDPE234GBS0 Unit had codes 4-3 and 7-1. Put into diag and unit would fill but sump not running. Installed new sump assembly in the unit and ran through a diagnostic test. All checks ok and is working correctly once again.; used 1 W11085683 (SUMP) from stock

Near Woodland Ave, Shakopee, MN 55379
Ryan W.

Ryan W.

REFRIGERATOR WHIRLPOOL WRV976FDEM01 Ice maker fill tube frozen in diag all thermistors and fans pass icebox is reading cooler than harvest which is good temps are ok no incoming water in diag ran 19 for heater test which thawed line. Will need new heater and ui ordrered; ordrng 1 W11226501 (HEATER) and 1 WPW10677104 (cntrl-elec)

Near Spring Lake Court, Shakopee, MN 55379
Nate A.

Nate A.

RANGE WHIRLPOOL MER6600FZ1 "Installed spring on the other side of door as well but proved too much for the unit and door wouldn’t lay flat, just wanted to spring right closed. Reinstalled the old hinge. Door is sealing fine and may just have to give the door a tiny push close at the end until the gasket flattens out a bit."

Near Cambridge Way, Shakopee, MN 55379
Nate A.

Nate A.

WASHER MAYTAG MVWC416FW0 Found a couple of coins in the space between the agitator and basket. Removed coins and ran unit through a recalibration and diagnostic test. No issues found through both of the test. Tenant had described the issue as the basket being stuck so possible the coins made the unit try to spin the basket as well on agitation. All checks ok currently.

Near Bluff Ave E, Shakopee, MN 55379
Nate A.

Nate A.

REFRIGERATOR WHIRLPOOL WRF560SMYM04 Thermistor checks ok and heater checks ok. Customer had the unit unplugged since Tuesday evening for this Friday morning appointment. EVAP had zero ice and the condenser pan was dry so don’t think there was ice buildup on the EVAP. Customer stated she saw a lot of frost on the EVAP cover and may have been hitting the EVAP fan. Door gasket looks like it’s sealing good. Added silicon sealant to the perimeter of the frame and cabinet joint.

Near Swaps Dr, Shakopee, MN 55379
Nate A.

Nate A.

RANGE WHIRLPOOL MER6600FZ1 Installed new control in the unit. If shutting the door gently the light inside the oven won’t shut off unless you push on the door a little then it would stay off. The design of this model has a spring on one side and a hinge on the other. Ordering an additional hinge with a spring to even out the door tension and help it shut. Verified the board with a 350 bake and achieved preheat and verified temp.; ordrng 1 WPW10299224 (hinge-door)

Near Cambridge Way, Shakopee, MN 55379