We serviced a
JENN-AIR WALLOVEN
Model JJW2830DP01
Near Eveleth, MN 55734
Dave
Job Details:
02/13/2023
Run oven and found off by 25 degrees and was able to adjust calibration up 25 degrees on both ovens and instruct customer on how to adjust if needed. Added service charge to icemaker service order.
We serviced a
WHIRLPOOL WASHER
Model WFW560CHW0
Near Minneapolis, MN 55414
Nate
Job Details:
02/13/2023
Installed new control in the unit and all is checking out correctly and is working correctly.
We serviced a
WHIRLPOOL MICROWAVE
Model WMH31017FS0
Near Minneapolis, MN 55401
Nate
Job Details:
02/13/2023
Intermittent condition with the microwave door switch. Installed updated style switch kit in the unit and all checks out good with no issues.
We serviced a
WHIRLPOOL DRYER
Model WED7990FW0
Near Minneapolis, MN 55414
Nate
Job Details:
02/13/2023
Installed new motor in the unit. Old (new) motor had a broken clip for the harness so maybe wasnt holding the harness on tight. All checks out good after installing new motor.
We serviced a
WHIRLPOOL WASHER
Model WFW560CHW2
Near Minneapolis, MN 55401
Nate
Job Details:
02/13/2023
Moved and unsure which unit it is now in. Left them the dispenser and wrote the serial number on the tag. They have about 200 vacants it may be in.
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF535SWHZ07
Near Cottage Grove, MN 55016
Dave
Job Details:
02/13/2023
"Replaced the water reservoir and water valve. There is slightly more water going out the reservoir, but after 20 minutes filling it is still only about 1.5 high in the reservoir. Called T Bruce and we adjusted the valve position so the water pressure was not on high. No improvement and there are no kinks in any visible water tubing. Bruce said since the valve is moving some water, and there is a spurt when the dispenser switch is pushed, we should reorder the filter head assembly even though it was just replaced. I tested it with the bypass cover on and water flow to the filter head assembly is strong.Return Thursday 2-16 from 3-5.; ordrng 1 W11346623R (Filter head assembly) and 1 W11346623R (Filter head assembly)"
We serviced a
WHIRLPOOL DISHWASHER
Model WDT750SAKZ0
Near Scandia, MN 55073
Matthew
Job Details:
02/13/2023
"Replaced both parts. Tested all buttons, functioning properly. Ran machine through diagnostics cycle, completed cycle with no errors."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRX988SIBM03
Near Chisago City, MN 55013
Matthew
Job Details:
02/13/2023
Found machine with a tear in the gasket for both the frozen and fresh compartment. Ordered both gaskets.; ordrng 1 W10407216 (Frozen gasket) and 1 W10846057 (Gasket)
We serviced a
WHIRLPOOL OVEN
Model WOD51EC0HS02
Near Minneapolis, MN 55449
Jay
Job Details:
02/13/2023
Cust has the console but does not have the blower assembly. Office please check and see if it was sen5; saved tckt
We serviced a
KITCHENAID REFRIGERATOR
Model KRFF507HPS03
Near Blaine, MN 55434
Jay
Job Details:
02/13/2023
"Icemaker failed, bad thermister. Ordering icemaker, cust will call when they get it; ordrng 1 W11579560 (Icemaker)"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF555SDFZ15
Near Ramsey, MN 55303
Lukas
Job Details:
02/13/2023
Customer stated one time he found eggs frozen on the middle shelf. Temps good today at 38 and 2. All components tested good in diagnostics. Customer will monitor temps.
We serviced a
WHIRLPOOL DISHWASHER
Model WDTA50SAKZ0
Near Elk River, MN 55330
Lukas
Job Details:
02/13/2023
The drain hose was loose where it connects to the air gap. Operation tested good after tightening.
We serviced a
JENN-AIR RANGE
Model JDS1750FS0
Near Big Lake, MN 55309
Lukas
Job Details:
02/13/2023
Installed console and harnesses.
We serviced a
KITCHENAID DISHWASHER
Model KDPM604KPS0
Near Osseo, MN 55311
Lukas
Job Details:
02/13/2023
The right hand hinge spring came out of place. Operation tested good after securing it and adjusting the hinge.
We serviced a
KITCHENAID BEVERAGE CENTER
Model KURL314KSS00
Near Plymouth, MN 55446
Lukas
Job Details:
02/13/2023
The lights are on but no other components run. Needs new control box.; ordrng 1 W11547447 (Control box)
We serviced a
KITCHENAID MICRO/OVEN
Model KOCE500EWH20
Near Plymouth, MN 55446
Lukas
Job Details:
02/13/2023
There is still play on the left upper corner after replacing the inner door and hinge. The outer door seems to be warped. Needs new outer door and gasket.; ordrng 1 W11600236 (Outer door) and 1 W11262567 (Gasket)
We serviced a
WHIRLPOOL DISHWASHER
Model KDTE304GPS0
Near Plymouth, MN 55446
Lukas
Job Details:
02/13/2023
Found a loose connection at the wash motor. Operation tested good after reseating the connection.
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF535SWHZ01
Near Plymouth, MN 55446
Lukas
Job Details:
02/13/2023
Installed new gasket. Needs new bin for customer to install.; ordrng 1 WPW10289497 and 1 Shipping
We serviced a
MAYTAG DRYER
Model MED6200KW0
Near Minneapolis, MN 55418
Lukas
Job Details:
02/13/2023
Installed new motor. Operation tested good.
We serviced a
WHIRLPOOL MICROWAVE
Model KMHS120ESS09
Near Otsego, MN 55330
Andrew
Job Details:
02/13/2023
"Light will not turn off, replaced control and install bulb cust had, unit now functioning okay inst cust to unplug unit when changing bulb to prevent in future, part covered unit warranty"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF535SWHZ02
Near Albertville, MN 55301
Andrew
Job Details:
02/13/2023
"Found damaged door, Installed door, unit tested ok sealing okay"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS325SDHZ08
Near Albertville, MN 55301
Andrew
Job Details:
02/13/2023
"Found damaged door, replaced door, unit tested ok"
We serviced a
WHIRLPOOL RANGE
Model WFE515S0JS
Near Monticello, MN 55362
Andrew
Job Details:
02/13/2023
"Unit tripping breaker again constantly when heating, needs new element, possibly backordered office to follow up ; ordrng 1 W11182108 (Element)"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRT112CZJZ00
Near Minneapolis, MN 55405
Dennis
Job Details:
02/13/2023
"Drain line blocked by ice build up in drain pan, removed ice, attached drain pan heater and adjusted to have better heat transfer at drain. Should no longer freeze up, advised it may drip into fridge but should clear up within 24 hours."
We serviced a
WHIRLPOOL RANGE
Model WEE510SAGS1
Near Minneapolis, MN 55404
Dennis
Job Details:
02/13/2023
Main control shorted out. Ordering control assembly to replace. Office to order and call to reschedule. ; ordrng 1 W10894098 (Main control) and 1 Parttotech
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRT318FZDW09
Near Minneapolis, MN 55406
Dennis
Job Details:
02/13/2023
"Replaced leaking filter dryer, recharged to factory specs. Allow 24 hours for temps to stabilize."
We serviced a
KITCHENAID RANGE
Model KFDC506JSS01
Near Minneapolis, MN 55417
Dennis
Job Details:
02/13/2023
"Door not sealing, ordering gasket to replace. Advised that very high moisture items may have some steam come out above door due to design of smoke vent. Cooling fan does come and and is functioning properly. ; ordrng 1 W11115330 (Gasket)"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRT318FZDM02
Near Minneapolis, MN 55419
Dennis
Job Details:
02/13/2023
"Unit has refrigerant leak, likely in evaporator. Complete no cool, would need compressor and evaporator replaced. Cost to repair more than replacing. Customer declined repair at this time."
We serviced a
WHIRLPOOL WASHER
Model WTW5010LW0
Near Cottage Grove, MN 55016
Aaron
Job Details:
02/13/2023
Vacuumed out stagnant water. Drain code. No power at harness connection of motor. Found lower harness broken will need new harness. Part shows eta tba. Ordering drain motor if needed after restoring power to drain motor. ; ordrng 1 W11399437 (Drain motor) and 1 W11643701 (Harness lower)
We serviced a
WHIRLPOOL DISHWASHER
Model WDTA50SAKZ0
Near Cottage Grove, MN 55016
Aaron
Job Details:
02/13/2023
Replaced dispener all test good no leaks
We serviced a
MAYTAG WASHER
Model MVW7232HW0
Near Long Lake, MN 55356
Ryan
Job Details:
02/13/2023
Noise seems to be coming from gearcase ; ordrng 1 W11449841 (Gearcase)
We serviced a
MAYTAG WASHER
Model MVWB765FW1
Near Eden Prairie, MN 55346
Ryan
Job Details:
02/13/2023
Could not duplicate at first empty running agitator had to load with towels and took about 20 min to get to act up sounds like dry bearing squeal in gearcase 175.00 labor 15.00 ship total =444.36Customer paid in full$444.36 CC Auth# Y4JE49; ordrng 1 W11393685 (Gearcase) and 1 Ship (Ship)
We serviced a
JENN-AIR RANGE
Model JGRP648HM01
Near Minneapolis, MN 55416
Nate
Job Details:
02/13/2023
When first trying ovens errored out within 30 seconds. Reset power F6E0 stored. Let the unit run and cycle running both ovens for about 45 minutes. Also ran some of the burners at the same time as the ovens and didnt effect the cycle temps. Both ovens cycling between 325 and 375 consistent on both ends within 5 degrees. Customer thermometers in the cavity show pretty consistent on both cavities with small oven showing 350 and large oven showing 330.
We serviced a
WHIRLPOOL DISHWASHER
Model WDF520PADM9
Near Farmington, MN 55024
Joshua
Job Details:
02/10/2023
Found faulty valve installed from stock and tested ; used 1 W11175771 (INLET VALVE) from stock
We serviced a
JENN-AIR RANGE GAS
Model jds9860aap
Near Minnetonka, MN 55305
Dennis
Job Details:
02/10/2023
"Right side module electrodes cracked, Ordering electrode kit to customer. Adjusted burners best I could. Advised left and right side valves are different BTU burners and wont match. ; ordrng 1 WP74005890 (Electrode kit)"
We serviced a
MAYTAG RANGE
Model MER6600FZ3
Near Eagan, MN 55122
Aaron
Job Details:
02/10/2023
"Replaced lf infinite switch. Talked about ceramic glass will retain heat even when off. Will take a while to cool down. This can also effect if you are going from extended time on hot to low. Ceramic glass will retain heat for some time. Will be most notible on higher watt burner lf is 3000, rf is 2500 watt"
We serviced a
WHIRLPOOL DRYER GAS
Model wgd7600xw0
Near Saint Paul, MN 55116
Aaron
Job Details:
02/10/2023
"Idler worn skreeching immediately when turned on. Replaced idler sounds good now, tumbling and heating. ; ordrng 1 Ship"
We serviced a
KITCHEN AID DISHWASHER
Model KDTM404KPS0
Near Saint Paul, MN 55104
Aaron
Job Details:
02/10/2023
"Heater replacement covered per s-code. Customer experiencing drain motor on lights flashing and inoperable. On arrival toe kick insulation wet and water in front tray. Finding heater gromets deteriated. Replacement of heater covered by warranty. Talked about potential of being other issues causing water in float assembly. Took pictures of damaged and sent to kitchen aid via link. Customer also stated prev dishwasher had also leaked. After replacing heater finding that wash motor does not turn on. Checked for voltage directly at wash motor. Is getting power. The repair of replacing the sump assembly would not be covered with heater replacement. Would need new call. Also potential of drip tray filling some other way. Seeing no leaks when testing, but wash pump not pumping at all. Water from heater leaking from gromet does line up with potential water dripping on sump motor. No way to know for sure if this caused issue with sump motor but let customer know may be worth reaching out to kitchen aid to see if there is anything they would do. ; used 1 W11537778 (Heater) from stock"
We serviced a
WHIRLPOOL WASHER
Model WFW72HEDW0
Near Saint Paul, MN 55107
Aaron
Job Details:
02/10/2023
Running to a gfci behind washer dryer stack tripped. No error codes and clearing diagnostic cycle without issue. Per manufacturer recommended to be on a time delay style breaker. Currently going to gfci outlet which is not recommended by manufacturer but may be required due to installation of washer and dryer in bathroom. Heavy oversudsing in diagnostic cycle. Talked about soap use and recommended wash cycle with no soap or cloths to get rid of excess soap.
We serviced a
JENNAIR DISHWASHER
Model JDPSS246LL0
Near Edina, MN 55436
Nate
Job Details:
02/10/2023
Installed new sump in the unit and ran through a couple of diagnostic tests. All checks out good and unit went through diagnostic tests with no issues or errors. All checks out good.
We serviced a
WHIRLPOOL DISHWASHER
Model WDTA50SAKZ0
Near Minneapolis, MN 55417
Nate
Job Details:
02/10/2023
Dimple in the gasket on the right corner. Could see moisture was leaking out of the corner. Installed new gasket in the unit and tested. All checks out good and is working correctly with no leaks.; used 1 W11483553 (Gasket tub) from stock
We serviced a
WHIRLPOOL WASHER
Model WFW5090JW0
Near Minneapolis, MN 55401
Nate
Job Details:
02/10/2023
Unit is trying to drain continuously even though it is empty. Gets stuck in C03 on the test mode. Will need new control to fix the issue. Office to get approval and schedule.; ordrng 1 W11616491 (Control)
We serviced a
WHIRLPOOL WASHER
Model WTW5100HW1
Near Corcoran, MN 55340
Joshua
Job Details:
02/10/2023
Drain pump came unplugged. Fastened it in properly and tested. All working as it should now.
We serviced a
MAYTAG DRYER
Model MGD6230HW0
Near Long Lake, MN 55356
Joshua
Job Details:
02/10/2023
Installed the new motor and tested. All working great now the motor stopped humming on start up.
We serviced a
KITCHENAID OVEN
Model KEBS207BSS01
Near Plymouth, MN 55446
Hung
Job Details:
02/10/2023
"Check over unit bottom door oven was lock out, unlock it checked fuse at control it was bad replace with new one, turn on breaker unit came back up ran bake cycle on both unit everything tested out good with heat..; used 1 WPW10545291 (Fuse) from stock"
We serviced a
WHIRLPOOL OVEN
Model KEBS109BSP00
Near Maple Grove, MN 55311
Hung
Job Details:
02/10/2023
"Install door seal and fuse, turn in breaker ran test everything tested out good reach temp to 350 at bakelook like its working properly.."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS325SDHZ08
Near Cottage Grove, MN 55016
Dave
Job Details:
02/10/2023
"Ms pic.Customer claims WO had her do a reset 2x prior to us being sent out. She lost food 3x now.Temperqture are 60 degrees in the fresh food section and 44 in the freezer.Not defrosting. When steaming away the ice on the evaporator, I saw the brown wire was loose on the harness that goes to the fan motor, Hester, defrost heater and defrost thermistor. The harness plugs into the back of the freezer. Unable to see the new part for the fan motor on a parts page or website enough to see if it comes with the needed harness. Office to do a parts research and follow up,with the customer. I was able to push the wire back into the connector and taped the wire in place, hoping to keep the unit cooling until the part arrives.; ordrng 1 Research (Wire harness described in the pvr)"
We serviced a
WHIRLPOOL RANGE
Model WFG505M0BS3
Near Woodbury, MN 55129
Dave
Job Details:
02/10/2023
Ms pic and update.The oven sensor is reading it to be 35 degrees room temperature and the door seal is off on the left side. The control board is sending voltqge to the ignitor. Both t bake ignitor and oven sensor are open.Return Thursday. 2-16-13.; ordrng 1 W11176454 (Bake ignitor) and 1 Wpw10181986 (Sensor) and 1 Wpw10535778 (Oven seal)
We serviced a
KITCHENAID DISHWASHER
Model KDTM404KPS0
Near Saint Paul, MN 55104
Dave
Job Details:
02/10/2023
"The dishwasher had been installed left side aligned so the hinge was lightly rubbing against the cabinet. The hinge spring connecting rod disengaged.I reattached it and center aligned the dishwasher, then opened and closed the door 20 times. Neither side was contacting the cabinet where the hinges are. Tested the unit in diagnostics and everything is good."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS555SIHZ03
Near Stillwater, MN 55082
Matthew
Job Details:
02/10/2023
"Found machine with ice in the end of the fill tube to the ice maker. Used hair dryer to remove ice and ran a small brush through to clear sediment. Tested ice maker, harvested normally. Tested fill, filled normally. The customer at the home decided that they didnt need me to wait on tech line for this issue at this time."
We serviced a
MAYTAG WASHER
Model MVW7232HW0
Near Saint Paul, MN 55117
Matthew
Job Details:
02/10/2023
"Replaced both parts. Ran machine through diagnostics cycle, completed cycle with no issues. Ran on high speed spin, functioning properly."
We serviced a
WHIRLPOOL DRYER
Model WHD560CHW2
Near Little Canada, MN 55117
Matthew
Job Details:
02/10/2023
Found machine not installed properly. There wasnt a drain hose installed. Customer didnt have the hose but plans on calling the install company to see if they have it. If she cant get one from the installation company then she will call us to order a new one.
We serviced a
WHIRLPOOL WASHER
Model MVWB765FW2
Near Hugo, MN 55038
Matthew
Job Details:
02/10/2023
"Replaced lid. Ran machine through diagnostics cycle, completed cycle with no issues."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF767SDHZ03
Near Ramsey, MN 55303
Jon W
Job Details:
02/10/2023
Replaced ice maker. I filled the ice maker in diagnostics. Then called tech line. He gave me the sr #77357705385.
We serviced a
WHIRLPOOL MICROWAVE
Model WML55011HS07
Near Blaine, MN 55434
Jon W
Job Details:
02/10/2023
Replaced the door.
We serviced a
KITCHENAID DISHWASHER
Model KDTM404KPS1
Near Minneapolis, MN 55410
Nate
Job Details:
02/10/2023
"Customer not home, talked to on phone and going to reschedule for next Thursday, am preferred for return.; schdld next appmnt for 2/16 THU AM"
We serviced a
KITCHENAID RANGE
Model KSGG700ESS3
Near Minneapolis, MN 55417
Dave
Job Details:
02/10/2023
Replaced the left side blower motor and tested. Heated the oven to 350 and the fan was nice and quiet.
We serviced a
MAYTAG DRYER
Model MGD5030MW1
Near Saint Paul, MN 55116
Dave
Job Details:
02/10/2023
Ms pic.The motor is buzzing and there is no obstruction in the blower wheel or at the deer wheel. Repalced the. Tor form truck stock and it is running quietly and heating well.; used 1 279827 (Motor) from stock
We serviced a
WHIRLPOOL RANGE
Model WEE510S0FW1
Near Apple Valley, MN 55124
Joshua
Job Details:
02/10/2023
Found faulty sensor unit is consistently off 100 degrees ; ordrng 1 W10833885 (Sensor) and 1 ShipToTech
We serviced a
WHIRLPOOL RANGE
Model WEG745H0FS1
Near Apple Valley, MN 55124
Joshua
Job Details:
02/10/2023
Found stuck key need to order display and overlay both at vadnais scheduled for Thursday ship to tech customer to be out of town ; ordrng 1 W11122852 (Display) and 1 W10728529 (Overlay) and 1 ShipToTech
We serviced a
WHIRLPOOL REFRIGERATOR
Model GI5SVAXVQ01
Near Rosemount, MN 55068
Joshua
Job Details:
02/10/2023
Collected 134 customer to wait to hear is lv board kit is available some with tk on issue
We serviced a
WHIRLPOOL DRYER
Model WED4950HW0
Near Rosemount, MN 55068
Joshua
Job Details:
02/10/2023
Found faulty thermal fuse causing issue installed WP3392519 from stock checked venting customer to handle ; used 1 WP3392519 (THERMAL FUSE) from stock
We serviced a
MAYTAG DRYER
Model MGD6230HW1
Near Rosemount, MN 55068
Joshua
Job Details:
02/10/2023
Installed parts
We serviced a
KITCHENAID DISHWASHER
Model KDTE334GPS0
Near Burnsville, MN 55337
Joshua
Job Details:
02/10/2023
"Found faulty sump customer paid in full scheduled for Thursday pm ; ordrng 1 W11178672 (Sump), used 1 Ship (Shipping/Handling) from stock"
We serviced a
KITCHENAID REFRIGERATOR
Model KRMF706ESS05
Near Burnsville, MN 55306
Joshua
Job Details:
02/10/2023
Unit leaking from valve and chattering air getting into system. Filter is out and pressure is great but is pulling in air causing dripping and leak at valve. Need to order W11482382 reservoir W11482383 dual valve W11482384 filter head W11579166 tube W11226501 heater fill tube W11484604 fill tube scheduled for Thursday ; ordrng 1 W11482382 (Reservoir) and 1 W11482383 (Dual valve) and 1 W11482384 (Filter head) and 1 W11579166 (Tube) and 1 W11226501 (Heater fill tube) and 1 W11484604 (Fill tube)
We serviced a
WHIRLPOOL WASHER
Model KAWS700JQ0
Near Lakeville, MN 55044
Joshua
Job Details:
02/10/2023
Found trans seal leaking bearing out due to this customer to buy new
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRX735SDHZ07
Near Lakeville, MN 55044
Joshua
Job Details:
02/10/2023
Door gaskets ripped need to order both ff gaskets at vadnais customer scheduled for Friday ; ordrng 2 W10830274 (Door seals)s
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF535SWHZ07
Near Waseca, MN 56093
Joshua
Job Details:
02/10/2023
Bad filter customer to get a new one an monitor
We serviced a
KITCHENAID DISHWASHER
Model KDTE334GPS0
Near Minnetonka, MN 55345
Joshua
Job Details:
02/10/2023
Pivot for the left side hinge broke off of the tub. Tub has lifetime warranty. Customer to pay for the labor and trip charge. Office to reschedule when part is available. Will be a 2 job count at least.; ordrng 1 W10713320 (Tub)
We serviced a
WHIRLPOOL WASHER
Model WFW85HEFC1
Near Prior Lake, MN 55372
Joshua
Job Details:
02/10/2023
Going to try an inlet valve assy. The water is now right on the sides but the inlet water temp is still too low. Office to order and reschedule since eta on my end is feb 28 for shipping.; ordrng 1 W10599356 (Inlet valve assy)
We serviced a
WHIRLPOOL DISHWASHER
Model WDF520PADM9
Near Prior Lake, MN 55372
Joshua
Job Details:
02/10/2023
Found there was no rinse aid in the unit for starters. Tested the unit in diagnostics to verify heater is irking as it should be. Heater is working as it should be. Just need to use the rinse aid in the unit and it should dry just fine. It is a plastic tub unit which tends to have extra condensation inside after use but rinse aid should clear it all up.
We serviced a
KITCHEN AID DISHWASHER
Model KDFE204KPS0
Near New Prague, MN 56071
Joshua
Job Details:
02/10/2023
Fill valve was stuck closed. Customer just happened to have one from a previous unit. Installed it and all is working great.
We serviced a
WHIRLPOOL DISHWASHER
Model WDT730PAHZ0
Near Blaine, MN 55434
Jon W
Job Details:
02/10/2023
"The water was shut off to the dishwasher. I turned it back on, and started up a cycle. Everything worked. I also replaced the pads on the door.; used 2 WP8268961 ( Pad) from stock"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS325SDHW08
Near Andover, MN 55304
Jon W
Job Details:
02/10/2023
I replaced the ice maker. Told customer to dump the first few trays of ice out.
We serviced a
WHIRLPOOL DRYER
Model WGD5100HW1
Near Otsego, MN 55374
Jon W
Job Details:
02/10/2023
"Customer said it only heats on certain cycles. I brought the back legs up a quarter of an inch, to help cloths hit the moisture sensor. I tested every cycle with some wet towels, and it heated every time."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRT311FZDW02
Near Elk River, MN 55330
Lukas
Job Details:
02/10/2023
Items soft in the freezer and freezing in the refrigerator. The refrigerator is in a garage where the temp is set to 50 degrees. I informed him the outside temp needs to be set to 60 for proper cooling. Customer will bump up the temp and see what happens.
We serviced a
WHIRLPOOL DISHWASHER
Model WDF330PAHB4
Near Elk River, MN 55330
Lukas
Job Details:
02/10/2023
Getting power into the pump but no water movement. Needs new sump assembly.; ordrng 1 W11025157 (Pump and motor)
We serviced a
MAYTAG REFRIGERATOR
Model MSS25C4MGZ06
Near Princeton, MN 55371
Lukas
Job Details:
02/10/2023
Installed new compressor. Customer will give it 24 hours to cool.
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRX735SDHV06
Near Oak Grove, MN 55011
Lukas
Job Details:
02/10/2023
Customer stated white particles once ice melts in a glass. I informed her this is calcium in the water and isnt harmful. The water out of the dispenser tested hard. Customer will call culigan to see what they can do to soften the water.
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF767SDHZ03
Near Minneapolis, MN 55448
Lukas
Job Details:
02/10/2023
The compressor is locked up. Needs new compressor.; ordrng 1 W11574734 (Compressor)
We serviced a
KITCHENAID ICEMAKER
Model KUIC15NLXS2
Near Maple Grove, MN 55311
Lukas
Job Details:
02/10/2023
The cutting grid is bad. Everything else checks good. Needs new grid. Quoted 90 labor.; ordrng 1 WP2313637 (Cutting grid) and 1 Shipping
We serviced a
KITCHEN-AID OVEN
Model KOSE900HSS00
Near Plymouth, MN 55446
Lukas
Job Details:
02/10/2023
The console harness came with just the ground wire that connects to the console. Not sure if its wrongly packaged or we ordered the wrong harness. Tk to send off to research to track down the correct harness.; saved tckt
We serviced a
KITCHEN AID MICRO/OVEN
Model KEMS306XWH4
Near Minneapolis, MN 55428
Lukas
Job Details:
02/10/2023
Customer stated one second into a microwave cycle it blows the thermal fuse. The first high voltage component to kick in is the transformer so I unplugged it to test. With the transformer unplugged it runs fine. Needs new transformer which is nla.
We serviced a
WHIRLPOOL OVEN
Model WOS51EC0HS20
Near Maple Grove, MN 55369
Hung
Job Details:
02/10/2023
"Check over unit called update line to verify if its up to date on software version, and it is, touch pad ui only works for couples of hours every time they have to reset break to use.."
We serviced a
WHIRLPOOL DISHWASHER
Model WDF540PADW3
Near Woodbury, MN 55125
Aaron
Job Details:
02/10/2023
"Water still in dishwasher on arrival. Drain hose plugged up at connection for house plumbing. Removed debris. Draining well not seeing leaks from anywhere. Talked about soap use, incoming water temp, and drying performance. All test good no leaks."
We serviced a
WHIRLPOOL DISHWASHER
Model WDT750SAKZ0
Near Cottage Grove, MN 55016
Aaron
Job Details:
02/10/2023
Replaced hinges and door gasket running diagnostic cycle. Am not seeing water in top left corner now. Customer will have to monitor and get back to us if needed. If needed would be looking to replace inner door panel and tub if issue still persist. Dishwasher is level.
We serviced a
WHIRLPOOL MICROWAVE
Model WMH31017HS08
Near South, MN 55016
Aaron
Job Details:
02/10/2023
Adjusted right panel. Appeared to be not sitting in flange correctly. No defect in outer cabinet and cavity is not an available part. Looks better than it did. Is past 30 days cosmetic. Any further action customer would want to reach out to Whirlpool directly. As is past cosmetic and is not a part that can be ordered. Pic taken of what looks like after adjusting.
We serviced a
WHIRLPOOL MICROWAVE
Model WMH53520CS5
Near Maple Grove, MN 55369
Hung
Job Details:
02/10/2023
Check over unit found bad door sw and bulb replaced both new parts ran test everything tested out good..; used 1 8206232A (Bulb) from stock
We serviced a
WHIRLPOOL WASHER
Model WTW4855HW2
Near Big Lake, MN 55309
Hung
Job Details:
02/10/2023
"Ran test on rinse and water was coming from tub ring, reorder tub ring per tim, office will call customer for return date..; ordrng 1 W11550886 (Tub ring)"
We serviced a
KITCHENAID DISHWASHER
Model KDTM404KPS0
Near East Bethel, MN 55092
Hung
Job Details:
02/10/2023
"Check over ran diagnostics found code for sump and board, part is on xpart..office to call customer for return date..; ordrng 1 W11416362 (Sump) and 1 W11410066 (Board)"
We serviced a
MAYTAG WASHER
Model MVW6200KW2
Near Blaine, MN 55449
Hung
Job Details:
02/10/2023
"Ran diagnostics and calibration everything tested out good no need parts, Ill hold on to part for 1-2 weeks just in case, unit is working properly.."
We serviced a
IKEA REFRIGERATOR
Model IX6HHEXDSM01
Near Minneapolis, MN 55416
Dennis
Job Details:
02/10/2023
"Ice maker not receiving power, thermal fuse blown, I replaced ice maker but still not getting water. Ordering valve to replace. Suspect valve shorted and caused ice maker fuse to pop. Office to order part and call to reschedule. ; ordrng 1 WPW10420083 (Valve), used 1 W10884390 (ICE MAKER) from stock"
We serviced a
WHIRLPOOL FREEZER
Model WZF34X16DW08
Near Minneapolis, MN 55416
Dennis
Job Details:
02/10/2023
"Installed new inverter, still not functioning. ; ordrng 1 W11572216 (Control) and 1 W11578208 (Compressor)"
We serviced a
WHIRLPOOL OVEN
Model WFG505M0BS3
Near Minneapolis, MN 55407
Dennis
Job Details:
02/10/2023
"Installed new gas valve, tested operations, oven works properly."
We serviced a
MAYTAG WASHER
Model MVW5430MW0
Near Bloomington, MN 55420
Dennis
Job Details:
02/10/2023
Unit missing impact absorber on right hand side. Ordering to replace. Office to order and follow up to reschedule. ; ordrng 2 WP8564458 (Absorber)s
We serviced a
MAYTAG REFRIGERATOR
Model MSD2572VES00
Near Minneapolis, MN 55423
Dennis
Job Details:
02/10/2023
"Unit not defrosting properly. Tested thermostat and heater at board, both check ok, indicates defrost board issue. Quoted 65$ labor to install new board. ; ordrng 1 WPW10366605 (Defrost control)"
We serviced a
WHIRLPOOL RANGE
Model WFE515S0JS3
Near Richfield, MN 55423
Dennis
Job Details:
02/10/2023
"Installed new control, tested cooktop and oven bake, all operations check ok."
We serviced a
WHIRLPOOL DISHWASHER
Model WDT710PAHZ1
Near Richfield, MN 55423
Dennis
Job Details:
02/10/2023
"Test ran unit, could not duplicate any leaks at this time, possible door interference."
We serviced a
WHIRLPOOL DRYER
Model WED560LHW2
Near Richfield, MN 55423
Dennis
Job Details:
02/10/2023
"Put unit into diagnostics, no error codes. Heating ok. Typical cause to this issue is not enough clothes to activate moisture sensor. Recommend running larger loads or using timed dry."
We serviced a
WHIRLPOOL MICROWAVE
Model WMH32517AT2
Near Edina, MN 55435
Nate
Job Details:
02/10/2023
All clips were in place for the control panel just fitting loose. Bent the brackets in so the would hold tighter in the slots. Fitting more snug now.